Home / Articles / Crooked Cabinet Doors Are Usually a Ten-Minute Fix. Here Is the Map
Home Maintenance Tips

Crooked Cabinet Doors Are Usually a Ten-Minute Fix. Here Is the Map

Misaligned kitchen and wardrobe doors are usually a hinge adjustment, not a new kitchen. Where the three screws go, and when the board itself has failed.

Published on November 15, 2026 · Updated October 30, 2026

You notice it in a reflection. The gap along one side of a kitchen door is wider at the top, the door rubs its neighbour when you close it, or a wardrobe door now sits proud and will not meet the magnet. Most people assume something has broken. On a fitted kitchen with standard concealed hinges, almost nothing has broken. The hinges have moved, or the doors have settled, and both are adjustable.

Here is how the adjustment works, what to do when it does not, and which symptoms mean you have a bigger problem than a screwdriver job.

How a concealed hinge moves a door

Most fitted kitchens and built-in wardrobes in Dubai use a 35 mm cup hinge: one part screwed into a bored hole in the door, one part screwed to the cabinet side, and the two clipped together. The mounting plate on the cabinet side carries the adjustment, and there are three directions of travel.

  1. Side to side. The screw nearest the door face, in the middle of the plate. Turning it swings the door in or out so the gaps on both sides of a pair match and the doors sit parallel. This is the screw you will use most, and it is usually all the fix you need for a door that rubs.
  2. In and out (depth). The screw or eccentric cam at the back of the plate. Loosening the fixing screws allows the door to move toward or away from the cabinet. This is what fixes a door that is proud at the top and tight at the bottom, and it is where the soft-close gap gets set.
  3. Up and down (height). The fixing screws in the slots of the plate. Slotted holes let the whole plate slide up or down before you retighten. This is how you align the top of a row of doors.

The major European hinge makers, and the unbranded copies used on plenty of fitted kitchens here, all work on that same principle: overlay adjustment, depth, height. Look at the plate before you turn anything and identify which is which.

The order that stops you chasing your tail

Adjusting doors in the wrong sequence is why people give up. Do it in this order, on the whole run, one pass at a time:

  1. Take everything off the doors and clear the worktop, so nothing is pushing a door out of place.
  2. Check the box first. Put a spirit level on the inside of the cabinet, top to bottom and side to side. If the carcass itself is out of level or racked, no hinge adjustment will hold and you are looking at furniture packing or a wall that has moved. Fix that before you touch a screw.
  3. Set the vertical alignment (height). Get all the tops in a row level and equal relative to the frame, worktop or the appliance above. Do the whole row before you go near the lateral screws.
  4. Set the horizontal gaps (overlay). Work door by door so the reveal between adjacent doors is even, front to back, within about a millimetre. Adjust one hinge at a time in small amounts, two full turns at most before you check.
  5. Check the depth. Close all doors and look along the run from the side. A door protruding slightly means the depth needs setting, or something inside is stopping it, or the box has swollen at the hinge line.
  6. Test the soft close. Open each door halfway and let it go; it should draw itself closed without a bang and without stopping short. Then open fully and check the damper still controls the last part of the swing.
  7. Tighten everything to a final torque feel, then re-check the row once. Hinges settle.

Half a turn is a lot on these plates. The mistake that ruins an afternoon is turning one screw a quarter of the way round too many times, then compensating on the other, and ending with doors worse than they started.

When adjustment will not fix it

Five things that look like a hinge problem and are not:

Stripped fixing holes. The classic on chipboard and MDF carcasses. The screws no longer bite, so the door sags again a week after you set it. Do not keep tightening. The proper repairs are: plug the holes with hardwood dowels or tightly packed toothpicks in wood glue, let it cure, redrill and refit; or move the plate to fresh timber; or fit a hinge repair plate that spans the damaged area. On a cabinet whose base has also gone soft, that is not a hinge job at all. Sagging doors on a sink-base unit are often the first thing people notice after a leak has swollen the carcass, and we cover that in water under the kitchen sink cabinet. If the leak is coming from a shower on the other side of that wall, water pooling in your shower floor is the next thing to check.

A swollen or delaminated door. If the door’s own edge has taken on moisture, the hinge cups have pulled loose from inside the bored hole and the door is loose at the hinge rather than misaligned. Run your fingernail along the door edge: a raised, fuzzy or cracked edge is a board problem, not a setting problem. If there is also a pale powdery bloom at the base of the wall behind it, the moisture is still active, and why white powder keeps appearing on your marble floor explains what that means for the structure.

A cracked hinge arm or a split cup. Common on the cheaper unbranded hinges used on budget fitted kitchens, especially on tall doors that carry too much weight on too few hinges. A cracked arm cannot hold a setting, and no adjustment recovers it.

A failed soft-close damper. If a door slams, or the damper leaves a sticky residue and stops mid-swing, the dashpot has lost its grease or the piston has seized. Dust plus old grease in this climate makes a grinding paste, and the damper is the part that dies first. Dampers on quality hinges are replaceable individually, so you do not need to re-hinge the whole kitchen.

A door that binds only in the summer. Timber and veneered doors swell with humidity swings, which is more common in rooms the AC does not keep dry, and in a villa that has been left unoccupied for a fortnight. The moisture mechanism across the whole property is in how Dubai summer heat quietly damages your home. If the door is fine in winter and rubs in August, plane a little off the rubbing edge and then seal the bare edge with paint or a lacquer, because an unsealed edge is what takes on the moisture in the first place.

Small things that make a big difference

  • Hinge count matters on tall doors. A full-height wardrobe door needs at least three hinges, and on a heavy door four. If the top hinge is doing all the work, that is exactly why it sags.
  • Do not oil a concealed hinge with thick grease. Grease holds dust, and dust is what grinds the mechanism. Clean first, and use a dry PTFE spray or a light machine oil on the moving parts only.
  • Tighten a loose cup by checking the screw heads inside the door. If they have sunk into the chipboard, the cup is pulling out and the door needs re-plugging, not re-tightening.
  • Adjust with the doors lightly loaded. Do not set a door with a pan on the inside of it.
  • Remove and clean the soft-close inserts if they have gone sticky, and check the small damper clip on the plate has not simply unclipped. Sometimes that is the whole fault.
  • Take photos of the gaps before you start, so you have a reference for what “even” looked like.
  • None of this applies to a fire door. There the closer is a life-safety component, and a door adjusted to be gentler can fail to latch, which is a separate subject covered in a fire door that won’t latch is not a nuisance problem.
  • Replace screws with the correct length. Longer screws into a thin cabinet side can punch through into the visible exterior of a run of units.

What a professional alignment visit involves

If a whole kitchen or a wall of wardrobes has gone, this is a genuine trade job rather than a Sunday afternoon, and it is quick when someone does it regularly. A proper visit covers: checking the boxes for level and square and packing or re-fixing where they have moved; replacing worn or cracked hinges and upgrading to quality soft-close units where the doors are heavy; re-plugging stripped holes rather than simply re-driving screws; resetting all doors to even reveal; replacing magnets and catch plates that no longer hold; and checking that drawers on runners have not racked, since a drawer that will not close pushes the door out of alignment above it.

Where the cause turns out to be water, that is a different job and it starts with finding the leak. We do both: carpentry and joinery for alignment, hinge and panel work, and kitchen when a carcass or a worktop edge needs more than adjustment. Send a photo straight on the affected doors, plus one of the inside of the cabinet with the door open, and we can usually tell you on the spot whether you need an hour of adjustment or a repair. Book it here, or read what clients say about our small-works jobs.

Frequently asked questions

Why have my cabinet doors suddenly gone out of alignment?

Usually one of three things. The box has moved slightly as a building settles or a fixing has loosened. The hinge screws have worked out of chipboard, which is extremely common. Or a door or carcass has taken on moisture and swollen. Sudden alignment loss across a whole run after a leak or a holiday points at the third.

Which screw adjusts a soft-close hinge?

On a standard concealed hinge, the screw nearest the door face in the middle of the mounting plate moves the door side to side. The screw or cam at the back sets the depth, and the plate’s slotted fixing screws set the height. Identify them before turning anything, because the same physical layout differs between brands.

My door closes but bounces back. What is that?

Most often the soft-close damper has failed or unclipped, or the door is meeting its neighbour before it reaches the catch. Check the gaps first, then the damper clip. A door that rebounds off a magnet usually needs the catch plate moved a few millimetres rather than a new hinge.

Should the doors be perfectly parallel?

The gaps should be even and the faces flush along the run. Absolute perfection on a fitted kitchen in a real building is not achievable, because walls and floors are not perfectly true, but a variation you can see in reflection is worth correcting.

Can I fix stripped hinge screws with filler?

Not with a general-purpose filler, no. The joint is carrying the door’s weight in shear. Pack the holes with hardwood dowels or toothpicks and wood glue, or use a hinge repair plate. Filler in a hinge hole fails within months.

How long does it take to align a kitchen?

Ten to twenty minutes for a handful of doors with the right sequence. Half a day for a whole kitchen where hinges need replacing and boxes need packing, which is also when it is worth having the drawers, doors and any water-damaged carcasses checked at the same visit. If you are preparing a rental for handover, aligned doors and working soft closers are on the fix list in the move-out walkthrough, and the same visit is a good moment to ask what else belongs in an annual maintenance contract.

Mukesh Bagra
Written by
Mukesh Bagra

Mukesh Bagra is the founder and lead stone specialist at ArabCare, Dubai's home and office maintenance company. Over 12+ years he has personally taken care of restoration projects of marble, tile and stone surfaces across the Marina, Palm Jumeirah and Downtown - from single-room polishing to full villa renovations. He writes ArabCare's guides to help Dubai homeowners spot problems early and care for their homes properly.

Dubai's trusted maintenance partner

Book your free visit in minutes.

Get a free on-site inspection from our specialists and receive a fixed price before any work begins.

  • Free on-site inspection Thorough assessment at no cost
  • Fixed price before we start No surprises, no hidden costs
  • Workmanship guarantee Quality you can trust, every time
Already worked with homeowners and offices like yours across Dubai.

Fast. Simple. Reliable.

Let's take care of it for you.

Book Your Free Visit

Or speak to a specialist

+971 50 469 1186 Mon to Sat, 8:00 to 19:00 GST
  • Licensed & Insured
  • DEWA Approved
  • Fixed price upfront